? semiconductor components industries, llc, 2014 august, 2014 ? rev. 10 1 publication order number: nl17sz86/d nl17sz86 single 2-input exclusive-or gate the nl17sz86 is a high performance single 2?input exclusive?or gate operating from a 2.3 v to 5.5 v supply. features ? extremely high speed: t pd 2.4 ns (typical) at v cc = 5.0 v ? designed for 1.65 v to 5.5 v v cc operation ? over voltage tolerant inputs ? l vttl compatible ? interface capability with 5.0 v ttl logic with v cc = 3 v ? lvcmos compatible ? 24 ma balanced output sink and source capability ? near zero static supply current substantially reduces system power requirements ? replacement for nc7sz86 ? nlv prefix for automotive and other applications requiring unique site and control change requirements; aec?q100 qualified and ppap capable ? these devices are pb?free and are rohs compliant figure 1. pinout (top view) v cc in b in a out y gnd in a in b out y = 1 figure 2. logic symbol 1 2 3 5 4 v cc a gnd y b 1 2 3 5 4 sot?353/sc70?5/ sc?88a sot?953 see detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. ordering information http://onsemi.com marking diagrams l8 m sc?88a / sot?353 / sc?70 df suffix case 419a m = date code a = assembly location y = year w = work week = pb?free package (note: microdot may be in either location) sot?953 case 527ae e = specific device code (e with 90 degree clockwise rotation) m = month code m 1 e
nl17sz86 http://onsemi.com 2 pin assignment (sot?353/sc70?5/sc?88a) pin 1 2 3 4 5 function in b in a gnd out y v cc input function table b l h l h output y l h h l a l l h h pin assignment (sot?953) pin 1 2 3 4 5 function in a gnd in b out y v cc maximum ratings symbol parameter value unit v cc dc supply voltage ?0.5 to 7.0 v v i dc input voltage ?0.5 v v i +7.0 v v v o dc output voltage output in high or low state (note 1) (sot?353/sc70?5/sc?88a packages) power?down mode ?0.5 v to + 7.0 v v o dc output voltage (sot?953 package) ?0.5 to v cc + 0.5 v i ik dc input diode current v i < gnd ?50 ma i ok dc output diode current v out < gnd, v out > v cc (sot?953 package) 50 ma i ok dc output diode current (sot?353/sc70?5/sc?88a packages) v out < gnd ?50 ma i o dc output sink current 50 ma i cc dc supply current per supply pin 100 ma i gnd dc ground current per ground pin 100 ma t stg storage temperature range ?65 to +150 c t l lead temperature, 1 mm from case for 10 seconds 260 c t j junction temperature under bias 150 c ja thermal resistance (note 2) 350 c/w p d power dissipation in still air at 85 c 150 mw msl moisture sensitivity level 1 f r flammability rating oxygen index: 28 to 34 ul 94 v?0 @ 0.125 in esd esd classification human body model (note 4) machine model (note 5) charge device model (note 6) class 1b class b n/a i latchup latchup performance above v cc and below gnd at 85 c (note 3) 500 ma stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device function ality should not be assumed, damage may occur and reliability may be affected. 1. i o absolute maximum rating must be observed. 2. measured with minimum pad spacing on an fr4 board, using 10 mm?by?1 inch, 2?ounce copper trace with no air flow. 3. tested to eia/jesd78 4. tested to eia/jesd22?a1 14?a, rated to eia/jesd22?a114?b. 5. tested to eia/jesd22?a1 15?a, rated to eia/jesd22?a115?b. 6. tested to jesd22?c101?a.
nl17sz86 http://onsemi.com 3 recommended operating conditions symbol parameter min max unit v cc supply voltage operating data retention only 1.65 1.5 5.5 5.5 v v i input voltage (note 7) 0 5.5 v v o output voltage (sot?353/sc70?5/sc?88a packages) (high or low state) 0 5.5 v v o output voltage (sot?953 package) (high or low state) 0 v cc v t a operating free?air temperature ?55 +125 c t/ v input transition rise or fall rate v cc = 2.5 v 0.2 v v cc = 3.0 v 0.3 v v cc = 5.0 v 0.5 v 0 0 0 20 10 5 ns/v functional operation above the stresses listed in the recommended operating ranges is not implied. extended exposure to stresse s beyond the recommended operating ranges limits may affect device reliability. 7. unused inputs may not be left open. all inputs must be tied to a high? or low?logic input voltage level. dc electrical characteristics symbo l parameter condition v cc (v) t a = 25 c ?55 c t a 125 c uni t min typ max min max v ih high?level input voltage 1.65 to 1.95 2.3 to 5.5 0.75 v cc 0.7 v cc 0.75 v cc 0.7 v cc v v il low?level input voltage 1.65 to 1.95 2.3 to 5.5 0.25 v cc 0.3 v cc 0.25 v cc 0.3 v cc v v oh high?level output voltage v in = v il or v il i oh = ?100 a i oh = ?3 ma i oh = ?8 ma i oh = ?12 ma i oh = ?16 ma i oh = ?24 ma i oh = ?32 ma 1.65 to 5.5 1.65 2.3 2.7 3.0 3.0 4.5 v cc ? 0.1 1.29 1.9 2.2 2.4 2.3 3.8 v cc 1.8 2.1 2.4 2.7 2.5 4.0 v cc ? 0.1 1.29 1.9 2.2 2.4 2.3 3.8 v v ol low?level output voltage v in = v ih i ol = 100 a i ol = 3 ma i ol = 8 ma i ol = 12 ma i ol = 16 ma i ol = 24 ma i ol = 32 ma 1.65 to 5.5 1.65 2.3 2.7 3.0 3.0 4.5 0.08 0.20 0.22 0.28 0.38 0.42 0.1 0.24 0.3 0.4 0.4 0.55 0.55 0.1 0.24 0.3 0.4 0.4 0.55 0.55 v i in input leakage current v in = 5.5 v or gnd 0 to 5.5 0.1 1.0 a i off power off leakage current (sot?353/ sc70?5/sc?88a packages) v in = 5.5 v or v out = 5.5 v 0 1 10 a i cc quiescent supply current v in = 5.5 v or gnd 5.5 1 10 a product parametric performance is indicated in the electrical characteristics for the listed test conditions, unless otherwise noted. product performance may not be indicated by the electrical characteristics if operated under different conditions. ac electrical characteristics t r = t f = 3.0 ns symbo l parameter condition v cc (v) t a = 25 c ?55 c t a 125 c uni t min typ max min max t plh t phl propagation delay (figure 3 and 4) r l = 1 m c l = 15 pf 1.65 2.0 6.9 13.8 2.0 14.5 ns r l = 1 m c l = 15 pf 1.8 2.0 5.7 11.5 2.0 12 r l = 1 m c l = 15 pf 2.5 0.2 1.2 4.1 7.0 1.2 7.5 r l = 1 m c l = 15 pf r l = 500 c l = 50 pf 3.3 0.3 0.8 1.2 3.0 3.8 4.8 5.4 0.8 1.2 5.2 5.9 r l = 1 m c l = 15 pf r l = 500 c l = 50 pf 5.0 0.5 0.5 0.8 2.2 2.9 3.5 4.2 0.5 1.0 3.8 4.6
nl17sz86 http://onsemi.com 4 capacitive characteristics symbol parameter condition typical unit c in input capacitance v cc = 5.5 v, v i = 0 v or v cc 7.0 pf c pd power dissipation capacitance (note 8) 10 mhz, v cc = 3.3 v, v i = 0 v or v cc 10 mhz, v cc = 5.5 v, v i = 0 v or v cc 9 11 pf 8. c pd is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption with out load. average operating current can be obtained by the equation: i cc(opr ) = c pd v cc f in + i cc . c pd is used to determine the no?load dynamic power consumption; p d = c pd v cc 2 f in + i cc v cc . figure 3. switching waveform input r l c l a 1?mhz square input wave is recommended for propagation delay tests. figure 4. test circuit t f = 3 ns v cc gnd v oh v ol 90% 50% 10% 50% t plh t phl output y input a and b t f = 3 ns 90% 50% 10% 50% output v cc or gnd device ordering information device package shipping ? nl17sz86dft2g sc70?5/sc?88a/sot?353 (pb?free) 3000 / tape & reel NLV17SZ86DFT2G* sc70?5/sc?88a/sot?353 (pb?free) 3000 / tape & reel nl17sz86p5t5g sot?953 (pb?free) 8000 / tape & reel ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d. *nlv prefix for automotive and other applications requiring unique site and control change requirements; aec?q100 qualified and ppap capable.
nl17sz86 http://onsemi.com 5 package dimensions notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. 419a?01 obsolete. new standard 419a?02. 4. dimensions a and b do not include mold flash, protrusions, or gate burrs. dim a min max min max millimeters 1.80 2.20 0.071 0.087 inches b 1.15 1.35 0.045 0.053 c 0.80 1.10 0.031 0.043 d 0.10 0.30 0.004 0.012 g 0.65 bsc 0.026 bsc h --- 0.10 --- 0.004 j 0.10 0.25 0.004 0.010 k 0.10 0.30 0.004 0.012 n 0.20 ref 0.008 ref s 2.00 2.20 0.079 0.087 b 0.2 (0.008) mm 12 3 4 5 a g s d 5 pl h c n j k ?b? sc?88a (sc?70?5/sot?353) case 419a?02 issue l mm inches scale 20:1 0.65 0.025 0.65 0.025 0.50 0.0197 0.40 0.0157 1.9 0.0748 solder footprint* *for additional information on our pb?free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d.
nl17sz86 http://onsemi.com 6 package dimensions sot?953 case 527ae issue e *for additional information on our pb?free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* e d c a h e 123 4 5 notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters 3. maximum lead thickness includes lead finish. minimum lead thickness is the minimum thickness of the base material. 4. dimensions d and e do not include mold flash, protrusions, or gate burrs. dim min nom max millimeters a 0.34 0.37 0.40 b 0.10 0.15 0.20 c 0.07 0.12 0.17 d 0.95 1.00 1.05 e 0.75 0.80 0.85 e 0.35 bsc l 0.95 1.00 1.05 h e x y pin one indicator b 5x x 0.08 y l 5x l3 l2 e 5x 5x l2 0.05 0.10 0.15 l3 ??? ??? 0.15 0.175 ref top view side view bottom view 1.20 dimensions: millimeters 0.20 5x 1 package outline 0.35 pitch 0.35 5x on semiconductor and are registered trademarks of semiconductor co mponents industries, llc (scillc). scillc owns the rights to a numb er of patents, trademarks, copyrights, trade secrets, and other inte llectual property. a listing of scillc?s pr oduct/patent coverage may be accessed at ww w.onsemi.com/site/pdf/patent?marking.pdf. scillc reserves the right to make changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and s pecifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including ?typical s? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the right s of others. scillc products are not designed, intended, or a uthorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in whic h the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or us e scillc products for any such unintended or unauthorized appli cation, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unin tended or unauthorized use, even if such claim alleges that scil lc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyrig ht laws and is not for resale in any manner. p ublication ordering information n. american technical support : 800?282?9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81?3?5817?1050 nl17sz86/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303?675?2175 or 800?344?3860 toll free usa/canada fax : 303?675?2176 or 800?344?3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your loc al sales representative
|
